|
Manufacturer |
Yr |
Model |
Description |
Qty |
LOC. |
|
Electrovert |
Vintage 1988 |
EPK II LV |
Manual controlled 16” Dual Wave Electrical 220 Volt Foam
fluxer “V” Finger conveyor - finger cleaner Electrovert
factory installed (year 2000) 2 each Vectra convection
preheaters (Lower only) Deflectors above Hood Lights Manual
width adjust S/N MOxxx 130 01-LV-080 FOB: Sherman TX.
|
1 |
FOB TX. |
|
Electrovert |
1992 |
EPK Plus |
Computer controlled 16” Dual Wave Electrical: 440 Volt 43
amps Foam fluxer “V” Finger conveyor - finger cleaner Two
lower, one upper preheaters, one deflector above first
bottom preheat, N2 blanket over last two preheaters N2
systems currently not operational Hood glass detectors, Hood
LightsManual width adjust Factory installed Nitrogen Blanket
S/N MOxxxx 220 66/001A
|
1 |
FOB: TX |
|
Electrovert |
1994
|
EPK I SMT |
Manual controlled 16” single wave No Omega Electrical 220
Volt 3 ph 86 amps “V” Finger conveyor - finger cleaner 2
lower, 1 upper preheater 1 deflector above 1st bottom
preheat Hood Lights Manual width adjust Footprint is: 9 ft
long at base, 10’2” long (from conveyor end to conveyor end,
4’7” wide 5’ 5” tall Holds 1220 # of solder S/N MOxxx
|
1 |
FOB TX. |
|
Electrovert |
1998 |
UPK 650 |
Manual controlled 20” Dual Wave w/rotary, Electrical 440
Volt 69 amps, Foam fluxer “V” Finger conveyor - finger
cleaner, 3 lower convection preheaters, deflectors above,
Hood Lights, Push button width adjust, S/N 118xxxx
|
1 |
FOB TX. |
|
Electrovert |
1998 |
UPK 650 |
Manual controlled 20” Dual Wave w/rotary, Electrical 440
Volt 69 amps, Foam fluxer, “V” Finger conveyor - finger
cleaner, 3 lower convection preheaters, deflectors above,
Hood Lights, Push button width adjust, S/N 118xxxx
|
1 |
FOB TX. |
|
Electrovert |
1996
|
UPK 650 |
Manual controlled 20” Dual Wave w/rotary, Electrical 440
Volt 69 amps, Foam fluxer, “V” Finger conveyor - finger
cleaner, 3 lower convection preheaters, deflectors above,
Hood Lights, Push button width adjust, S/N 96090xxxc.
|
1 |
FOB TX. |
|
Electrovert |
1988 |
Econopak II SMT
|
the Fluxer is 2000, and the machine was refurbished in 2000,
Computerized 16” wave solder machine, Nordson PulseSpray
PSRA spray fluxer, 2 lower quartz IR preheaters with upper
tunnel, Roll out solder pot with Lambda, Omega and turbulent
waves, Finger cleaner, Interior lighting, Manuals, Computer
and software. LV115, Electrical: 208 volts, 3 phase, 59
amps.
|
1 |
FOB west coast |
|
Electrovert |
March 2000 |
Vectra |
Foam fluxer, 220 v 3 ph, Manuals included, Lead Free Pot -
450/F wave solder, Below is the original configuration from
Electrovert, 1 VC-1100698-01 VECTRA Wave soldering
System, OPTION
DESCRIPTION QTY
OP-BASE-VC Vectra Base Machine 1
OP-FLXI-VC Flexible Intermix
fingers 1
OP-FCLR-VC Finger Cleaner 1
OP-MWTH-VC Motorized Width Adjust 1
OP-VEC-VC Vecta Heater 3
OP-FOAM-VC Foam Fluxer Option 1
OP-CER-VC Ceramic Aerators 1
OP-EXTFLX-WS External Fluxe Cabinet 1
OP-AIR-WS Lambda Wave 1
1 VC-1100698-01
OP-AIRROT-WS Air Rotary Chip 1
OP-MROLL-VC Motorized Rollout/Jack 1
OP-OUTPUT-WS Output Photocell 1
OP-MNLS-WS English Manuals 1
QWS-11879132-02 CBS 1
MACHINE SPECIFICATION NOTES: 220 Volts - 60 Hertz - 3
Phase, VVL Finger Intermix Ratio, 1/16INBoard Thickness, 3.0
mm foot length, Load Guides at board input, Zone 1: Vecta
Preheater, Zone 2: Vecta Preheater, Zone 3: Vecta Preheater,
English Machine Manuals, FOB: Sherman TX. |
1 |
FOB TX. |
|
Electrovert |
1994
|
UPK 640C M/F |
Vintage (manufactured 11/94), Computer or Manual controlled
18” Dual Wave, Electrical 440 Volt 3 ph 79 amps, Spray
fluxer , “V” Finger conveyor - finger cleaner, 3 lower
convection preheaters, deflectors above, 1 upper IR
preheater, Hood Lights, Lead free solder pot, Manual width
adjust, Left to right flow, Nitrogen ready, S/N MO9409xxxxx
|
1 |
FOB TX. |
|
ELECTROVERT |
|
Econopak 11 SMT |
|
1 |
USA |
|
ELECTROVERT |
|
Ultrapak 445 18"" |
|
1 |
USA |
|
|
